How to paint a radiator

As you look around your house, you may find that some of the main fixtures and fittings are in need of a bit of a facelift.

Image Credit

Almost every room in your home likely boasts a radiator, unless you have underfloor heating. Their painted finish will deteriorate through use, and you may want to bring them back to life with a lick of paint. How should you go about it?


There are different types of radiators ranging from classic old-style radiators to column radiators and convection radiators. The modern trend for column radiators means you may wish to replace rather than upgrade.

Examples can be found at

The easiest way to upgrade existing radiators for those afraid of DIY would be to go to the professional body for painters and decorators and source a professional, but if you want to have a go, here are some tips.

Keep in mind it is not like painting a wall or woodwork; there is a lot more to it than that.

Image Credit

First, make sure the heating is turned off or the radiator is isolated from the system via the control valve. Next, give the radiator a good cleaning, removing dust and any loose debris.

Give the dry radiator a gentle rub with a fine sandpaper and remove any rust with a wire brush.

Put down a dustsheet and place masking tape on any surrounding areas.

Specialist primers are available for radiators to cover any rusted or bare spots to provide a base.


Do not use just any paint; seek out a heat-resistant alternative. Specialist radiator paints are available that will help prevent heat discolouring. You can use a clear radiator overcoat over an ordinary emulsion, but a radiator paint is preferable.

Although a radiator spray paint provides a good finish, you will need to remove the radiator first. Then, open a window for ventilation and begin to apply your paint in long, even strokes, following the contours of the surface wherever possible. If you are struggling, an angled radiator brush may help.

Add a second top coat 24 hours later. You may want to wait a further couple of days before turning the radiator back on. You may notice a smell coming from it once it is back on, but this will quickly fade.


How to look after your crystal chandelier

Many owners of crystal chandeliers avoid the job of cleaning their prized possession because the thought of taking each crystal down and washing them individually is an arduous task. Here we take a look at the different cleaning options.

Image Credit

In essence, whether you own several antique crystal chandeliers or an inexpensive modern one, the key is to clean little and often with a feather duster. That way, dust particles won’t dull the crystal drops.

How often should you clean your crystal chandelier?

Check when your crystal chandelier was made. Those that were made within the last ten years need less cleaning because they have a coating on them that helps to repel dust. As soon as it starts to lose its sparkle and shine, you will know it is time for a clean.

The drip-dry approach made easy

Use a crystal cleaner or glass cleaner and take the following steps :
•       Switch off the ceiling light.
•       Remove the lamps and plug the sockets so liquid can’t get into the connections.
•       Place a covering on the floor to soak up any excess water.
•       Use a generous amount of spray all over the chandelier and allow it to fall off naturally; this will take the dust with it.
•       Use a dust mask and make sure the room is well ventilated.
•       Allow the light fitting to dry out completely before putting the lamps back in place.
•       Wipe the bulbs and switch on. Your chandelier, like the ones at, will be sparkling again!

Image Credit

The glove method

  •      Wear white cotton gloves and use chandelier or glass cleaner. Again, make sure the electricity is switched off.
    •       Use a step ladder and position it under the light fitting. Place your fingertips in the solution and run along each crystal strand.

    The complete removal

In some cases, the only way to clean a chandelier is to wash each drop by hand. It’s worth taking a photograph of the chandelier so each one is put back in the right place. You can even watch a video.

Remove each one and clean in warm soapy water before rinsing in cold water. Dab each one dry and replace. The process will be worth it!
Finally, remember to dust every week and undertake an annual thorough cleaning. Then sit back, relax and enjoy!

Top Tips for Successfully Installing Your Floor

Installing your floor can be difficult. Experts advise that you should do the following to ensure the finished product lives up to your expectations.

Image Credit

Measure the Area

Make sure the area has been accurately measured. If you have not done this, you may have a tapered last row, and this will be unattractive and will require covering. Measure to begin with and allow for the irregularities by planning to taper your first and last row.

Preparing the Area

Before installing your floor, make sure the area is clear of debris. Remove any nails or staples and dust/vacuum the subfloor before beginning that installation. If you need to, sand the subfloor to ensure smoothness.


When sticking the underlay down, make sure you use the correct tape, as failure to do so may result in crinkling when it’s stepped on.

Image Credit


When cutting the floor, use the appropriate shear recommended by the engineered flooring company such as This is also a more convenient method than using a saw.


Start working under doorways, as the chances are you won’t want to finish the job doing this.


When moving to a new room, leave a little gap to be filled with a transition strip to differentiate between rooms. Position the gap under the door to form a break between rooms.


It can be very helpful to use a piece of flooring to tap boards into place, especially when they are difficult to position.

Looking After Your Boiler


Boiler breakdowns always seem to occur at the worst possible time when the winter weather is upon us. That’s normally because they have been sitting idle all summer and are then suddenly required to work flat out when autumn and winter descend. Boiler problems can be both inconvenient and expensive, but there are things you can do to look after this important investment. Prevention can save you a lot of money and hassle, so what should homeowners be doing to prepare for the colder months:

Regular Servicing

One of the best ways to keep your boiler in tip top condition is to have it serviced regularly and the recommendation is for an annual service to avoid the disruption of a breakdown. A gas safety engineer can come and do this for you to give you peace of mind that your boiler is in good working order. For Boiler Installation Gloucester, visit

Pipe Insulation

By insulating your pipes, you’ll stop them from freezing up when the temperature drops below zero. This helps to prevent the boiler’s condensate pipes from seizing up during the winter months which is major cause of boiler breakdown. Insulation for pipes is fairly cheap and can be purchased in local DIY shops.

Image credit


Taking care of your central heating

By taking care of your central heating system as a whole is a great way to reduce the chances of suffering from a boiler breakdown.

Bleeding your radiators is a simple job that can help remove excess air trapped inside them. If you’ve noticed that some of your radiators are warmer at the top than the bottom, then air is trapped in the system. You’ll need to release that air as it’s a sign your system isn’t working as efficiently as it should be and costing you extra in wasted energy.

Bleeding a radiator is a straightforward job. Make sure the heating is turned off before putting the radiator key into the slot on the valve. Twist the key anticlockwise about 45 degrees and you should hear the sound of air hissing. Have a rag or old towel to hand to catch any water that drips. Lock the valve back up and the job should be done.

Image credit


Put the heating on

A boiler that sits idle for months could be prone to seizing, so it’s always a good idea to turn your heating on occasionally just to keep the system active. During the summer, it is recommended that you run the heating occasionally for about 15 minutes.

Boiler pressure

Over time, a boiler can lose some pressure which results in them running less efficiently. Take a look at the pressure gauge on your boiler to see if it might need topping up. You will probably need to refer to the manual or contact a boiler specialist.


Why silicone is the first choice for many applications

Silicone is a great choice of material for many different purposes. The reason for this is that it has many useful properties that make it ideal for use in many industries.

Image Credit

Temperature resistant

Silicone has a high temperature resistance, which means it can withstand being used in very hot and very cold environments. It retains its elasticity in extreme temperatures and does not go brittle when freezing or become damaged in the heat. Silicone is therefore ideal for applications in which protecting against temperature damage is useful, such as in house paint.

Fire resistant

Silicone is also highly resistant to flames, making it stable and unlikely to catch fire. Electronic applications are therefore ideal places to use silicone, especially where the item needs to self-extinguish quickly such as in computers and ovens.

Silicone hoses from suppliers such as can be useful in industry. An example is the automotive industry, where high temperatures are found and stable hoses are needed.

Image Credit

Hard wearing

Silicone is highly durable, which is one of the reasons it is used in medicine. Silicone is used for implants because it is strong and resists wear, is accepted by the body and is permeable, which means some substances can pass through it. Silicone can also be used to protect a wound while it heals, acting as a useful seal.

Sealing properties

As silicone is good as a seal, it is used not only in medicine but also in construction. Silicone seals can be used in cockpits of planes and in doors of cars and houses to keep draughts out. Seals are also useful to protect the corners of a bath.

One problem with using silicone sealant around a bath in this way is that it can become mouldy due to the damp, which encourages fungal spores. If you need to remove the sealant, it is best to cut off the majority with a blade then use a pan scourer to remove the remainder. You can also put new silicone sealant on top of old sealant, as they will bond together.

The strong properties of silicone make it the first choice for many applications. From sealant to medical implants and ovens to computers, you will find silicone everywhere thanks to its temperature resistance, durability, stability and safety.